picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 1 of 8 features >55 db cm attenuation at 250 khz >70 db dm attenuation at 250 khz 40 vdc (max input) 12 amp rating 100 vdc surge 100 ms 707 vdc hi-pot hold off to shield plane 1.0?x 1.0?x 0.2?sip (system-in-package) ? mt land grid array (lga) -40 to +100? pcb temperature (see fig. 5) active filtering reduces volume and height efficiency 99% at full load connect in series for higher attenuation t?v approved applications ? ndustrial bus supplies telecom base stations cots systems t ypical application qpi performance ry= 10 ? , 1/4 w figure 1 - qpi-2 circuit on input bus. figure 2 - attenuation curves showing common-mode and differential-mode attenuation. description the qpi-2 active emi filter attenuates conducted common-mode (cm) and differential-mode (dm) noise over the cispr22 frequency range of 150 khz to 30 mhz. the product is designed for use on a 24 vdc bus (10-40 vdc). the qpi-2? 12 a rating supports multiple dc-dc converter loads up to a pcb temperature of 60?. at a 100? pcb temperature the qpi-2 supports 10 a loads. designed for a nominal 24 v bus, the qpi-2 supports industrial and cots applications. in comparison to passive solutions, the use of active filtering reduces the volume of the common-mode choke, providing a low profile, surface mount device. smaller size saves valuable board real estate and the reduced height enhances airflow in blade applications. the qpi-2 is available in a 1.0" x 1.0" x 0.2" sip (system in package) with lga mounting. qpi-2-eval1 kits are available for testing the qpi-2. the evaluation board has a mounted qpi-2 with screw terminals for quick in-circuit testing. check picorpower.com for the qpi-2-eval1 evaluation board and the qpi-an1 application note. QPI-2L quietpower 12 amp active emi filter for 24 v dc bus
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 2 of 8 absolute maximum ratings ? exceeding these parameters may result in permanent damage to the product. electrical characteristics ? parameter limits apply over the operating temp. range unless otherwise noted. pins parameter notes min max units bus+ to bus- input voltage continuous -0.5 40 vdc bus+ to bus- input voltage 100ms transient -0.5 100 vdc bus+/bus- to shield plane bus inputs to shield hipot per test std. +/-500 vdc qpi+ to qpi- input to output current continuous @ 25? 12 adc package power dissipation v bus = 24 v, i bus = 12 adc, 25? 4.0 w package operating temperature pcb to qpi interface -40 100 ? package thermal resistance free air 50 ?/w package junction temperature internal @ pdmax and 15?/w 160 ? package thermal resistance pcb layout (see figs. 9 & 10) 1 15 ?/w package storage temperature -40 125 ? package re-flow temperature 20 second exposure @ 212 ? all pins esd hbm +/-2 kv parameter notes min typ max units bus+ to bus- input range measured at 10 a 2 10 40 vdc bus+ to qpi+ voltage drop measured at 10 a 2 -300 mvdc bus- to qpi- voltage drop measured at 10 a 2 20 mvdc common-mode insertion loss v bus = 24 v frequency = 500 khz 60 db differential-mode insertion loss v bus = 24 v frequency = 500 khz 85 db input bias current at 40 volts input current from bus+ to bus- 17 ma note 1 - refer to figures 9 & 10 for pcb layout guidelines to achieve this thermal resistance when re-flowed onto the pcb. pad designations bus+ bus- qpi+ qpi- therm 1 shield therm 2 12,13,14 1,15,16 7,8,9 2,3,4 10 5,6 11 bus- bus+ qpi+ shield therm 1 therm 2 7 8 91112 13 16 10 14 15 1 2 3 4 5 6 qpi- pad description bus- negative bus potential bus+ positive bus voltage qpi- negative input to the converter qpi+ positive input to the converter therm1 internal connection must be electrically therm2 floating but maximize copper landing for heat sinking. shield the shield connects to the converter shield and y-capacitor common point through ry. note 2 - refer to figure 5 for current derating curve. qpi-2: (bottom view)
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 3 of 8 applications information the qpi-2 is an active emi filter providing conducted common-mode and differential-mode attenuation from 150 khz to 30 mhz. the qpi-2 attenuates noise at all frequencies covered by en55022. designers should be aware that to select and qualify an emi filter they must test the filter in their equipment under the set up and conditions specified in the emi standards that they are trying to meet. filter performance is highly dependent on several factors and cannot be derived from the attenuation curves shown in figure 2 alone. performance is a complex function of filter element impedances and noise source impedances, which vary in magnitude and phase over the frequency spectrum. measurements should be made in consultation with in-house compliance testing or an independent emi test facility. t est example figures 3 and 4 show the before and after plots of a dc-dc converter noise profile to demonstrate the performance of the qpi-2. the plots were taken using the standard measurement technique and set up defined in cispr22. the results show the total noise spectrum for a standard dc-dc converter under load compared to the en55022 class b quasi-peak detection limit. the resulting plot in figure 4 shows the qpi-2 is effective in reducing the total conducted noise spectrum measured pre-filter to well below the en55022 class b quasi-peak detection limit. layout and circuit application of the qpi-2 requires pcb layout practices similar to those used with passive emi filters. the circuit in figure 6 and the pcb layout in figures 9 & 10 should be used as a design guide to ensure successful application of the qpi-2. refer to the application note qpi- an1 for additional pcb layout recommendations. note: for optimum performance of the qpi-2 it is critical to connect the qpi-2 shield plane (pins 5 & 6) to the converter emi shield plane (common point of c1- c4"y" capacitors) thru ry as shown in figure 6. if the safety earth-ground connection (chassis or case) is connected in the power conversion section of the pcb it should be at the input bus of the qpi-2 shield plane, shown as the optional connection in figure 6. connecting the converter emi shield plane directly to chassis ground may degrade the qpi-2 attenuation performance. the typical value for ry is 10 ohms. the recommended part is a 5% tolerance smt1206 or similarly rated 0.25 w through-hole resistor. qpis will filter multiple dc-dc converters up to the maximum current rating. the schematic in figure 7 shows the required circuit for multiple dc-dc converters. the shield plane should be added under each converter as a common emi shield. note that only a single ry is required in a multiple converter configuration. figur e 3 conducted emi profile of a dc-dc converter without filter. figur e 4 conducted emi profile of a dc-dc converter with qpi-2.
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 4 of 8 figur e 6 recommended schematic for qpi. values of c in and c1-c4 should be the values recommended by the converter manufacturer. if the manufacturer does not specify a value for the y-capacitors use 4.7nf. ry=10 ? , 1/4 w. part number description QPI-2L qpi-2 land grid array ordering information bus+ qpi+ bus- qpi- shield bus supply qpi v in + v out + v in -v out - shield converter optional connection c1 c2 c3 c4 ry pcb plane under converter c in cb 47 f if higher attenuation is required, qpis can be connected in series. figure 8 shows the proper schematic for qpis in series. note that only one ry is required in this configuration. the qpi can also be used to filter embedded or ?own converters made up of discrete components. where ever possible a shield plane and y-capacitor decoupling should be included in the embedded converter design. follow the circuit and layout recommendations for a brick converter shown in figures 7, 9 & 10 . thermal considerations the current derating curve shown in figure 5 should be used when the pcb temperature in close proximity of the qpi-2 exceeds 60?. for example, the qpi-2 will support up to 10 a of current or 280 w from a 28 vdc bus at an 80? interface temperature. temperature should be measured at the pcb interface to the qpi-2 on the bus +/- pads or the qpi+/- pads. refer to figures 9, 10 & 12 for pcb layout recommendation. 01020304 05060708090100 pcb to qpi interface temperature (deg. c) qpi current (a) 14 12 10 8 6 4 2 0 figur e 5 qpi-2 current derating curve.
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 5 of 8 figur e 7 schematic for supporting multiple dc-dc converters. note only a single ry is required. use values recommended by converter manufacturer for c in and y-capacitors c1-c8. bus supply v in +v out + v in -v out - shield converter optional connection c2 c3 c4 ry pcb plane under converter c in 1 bus+ qpi+ bus- qpi- shield qpi cb 47 f c1 v in +v out + v in -v out - shield converter c6 c7 c8 pcb plane under converter c in 2 c5 additional converters 10 ? , 1/4 w figur e 8 series connection of qpi for higher attenuation. bus+ qpi+ bus- qpi- shield bus supply qpi v in +v out + v in -v out - shield converter optional connection c2 c3 c4 ry pcb plane under converter c in bus+ qpi+ bus- qpi- shield qpi cb 47 f c1 10 ? , 1/4 w
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 6 of 8 ry c1 c2 c4 c3 bottom layer - top view shield plane thermal 1 thermal 2 qpi shield cb c in top layer - top view thermal 1 thermal 2 shield plane c onverter ++ out - out c onverter - * * * * * + + fig ure 9 recommended layout for top layer of pcb. pattern shows optional pins (*) dependent on converter used in design. (actual size with half brick footprint) fig ure 10 recommended layout for bottom layer of pcb. note location of ry.
picor corporation ?www.picorpower.com QPI-2L data sheet rev. 2.0 page 7 of 8 0.000 0.100 0.300 0.492 0.441 0.441 0.100 0.300 0.492 0.000 0.100 0.300 0.492 0.400 0.441 0.441 0.400 0.100 0.300 0.492 qpi sip package (bottom view) 0.9843 0.8000 0.9843 0.0200 0.1773 13 places 2 places 45.000 0.1250 0.0820 0.0625 0.0820 0.0820 r0.0410 0.1310 0.0880 0.0655 0.0440 0.0440 0.0880 2 places 13 places 0.0000 0.1000 0.3000 0.1000 0.3000 0.3970 0.3970 0.4410 0.4410 0.4850 0.4850 0.0000 0.1000 0.3000 0.4410 0.3970 0.4850 0.0000 0.1000 0.3000 0.3970 0.4850 qpi package outline qpi pcb pad pattern (top view) r0.0440 bus- bus+ qpi+ shield qpi- therm 1 therm 2 0.4410 0.050 0.050 0.050 0.050 0.050 0.050 0.4410 0.492 fig ure 11 qpi package dimensions and pad locations. fig ure 12 recommended pcb layout pattern. use 1.3mm clearance around shield pads 5 & 6 to adjacent lands. see figures 9 & 10 for recommended connection layouts.
picor corporation ?www.picorpower.com ?QPI-2L data sheet p/n 27779 rev. 2.0 10/04/10m vicor? comprehensive line of power solutions includes high-density ac-dc & dc-dc modules and accessory components, fully configurable ac-dc & dc-dc power supplies, and complete custom power systems. information furnished by vicor is believed to be accurate and reliable. however, no responsibility is assumed by vicor for its use. no license is granted by implication or otherwise under any patent or patent rights of vicor. vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. all sales are subject to vicor? terms and conditions of sale, which are available upon request. specifications are subject to change without notice. vicor corporation 25 frontage road, andover, ma, usa 01810 tel: 800-735-6200 fax: 978-475-6715 email vicor express: vicorexp@vicr.com technical support: apps@vicr.com
|
