do not scale from this print .285 7.24 ref .505 12.83 ref "a" "a" mmss-05-22-x-xx.xx-s shown fig. 1 ipd1-xx-s (no of pos x .100[2.54]) + .055[1.40] ref .300 7.62 ref .200 5.08 ref .010 ref 0.25 (see note 9) 01 02 c l = dwc + .250[6.35] xx.xx .125[3.18] section "a"-"a" dwc-xx-10-300 c1 c-179-xx-x d mmss-xx-xx-x-xx.xx-x-x-xxx no of positions -02 thru -10 -s: single end -d: double end(must choose from last set of options.) plating specification -f: flash selective (use c-179-xx-f) -l: light selective (use c-179-xx-l) -s: selective (use c-179-xx-s) wire gauge (awg) -20 -22 -24 -26 -28 -30 end option [available on -d end option only & applies to end 2 housing] -lus: latch up, straight -lds: latch down, straight option specify in inches [use dwc-xx-xx] (single end: 03.00[76.2] inch minimum, double end: 03.25[82.6] inch minimum) assembled length option *-k: keyed polarization (use ipd1-xx-s-k) (see fig. 3, sheet 2) = dwc + .500[12.70] xx.xx .125[3.18] fig. 2 mmss-05-22-x-xx.xx-d-lus shown c2 * not released for production c sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [0.3] 2 .xxx: .005 [0.13] .xxxx: .0020 [0.051] material: .100[2.54] socket discreet cable assembly by: mmss-xx-xx-x-xx.xx-x-x-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 05/03/2005 2 1 sheet scale: 1.5:1 housing: nylon 6/6, color: white contact: phos bronze cable; insulation: pvc wire: tinned copper f:\dwg\misc\mktg\mmss-xx-xx-x-xx.xx-x-x-xxx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: .003[0.08] max. 3. parts to be molded to position. 4. minimum pullout force: 5 lbs [2.22 n]. 5. contact must be inserted until retention feature locks into place. 6. all finished goods are to be electrical tested including hi-pot test. 7. tinned copper wire contains lead. 8. parts are to be layer packaged. 9. contacts offset for polarization. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision d
-lus latch- end 1 latch- end 2 [latch up- cable straight] -lds latch- end 1 latch- end 2 [latch down- cable straight] .038 ref 0.96 .029 ref 0.73 ipd1-xx-s-k d * not released for production -k: keyed polarization (mmss-06-xx-x-xx.xx-x-k-xxx shown) (same as fig. 1, unless otherwise stated) fig. 3 sheet of .100[2.54] socket discreet cable assembly by: mmss-xx-xx-x-xx.xx-x-x-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 05/03/2005 2 2 sheet scale: 1.5:1 revision d f:\dwg\misc\mktg\mmss-xx-xx-x-xx.xx-x-x-xxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|