t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 1 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com applications ? mobile infrastructure ? lte / wcdma / cdma ? catv ? point to point ? general purpose wireless sot - 89 package product features ? dc - 6000 mhz ? robust class 2 (>2 000v ) hbm esd rating ? 19 db gain at 1.9 ghz ? 4.7 db noise figure at 1.9 ghz ? + 31.7 dbm output ip3 at 1.9 ghz ? +19.6 dbm p1db at 1.9 ghz ? 50 ohm cascadable gain block ? internal active bias ? sot - 89 p ackage functional block diagram rf in gnd rf out gnd 1 2 3 4 pin configuration pin no. label 1 rf in 3 rf out 2,4 gnd general description the tqp36 9185 is a general - purpose buffer amplifier that offers high dynamic range in a low - cost surface - mount package. at 1.9 gh z, the amplifier typically provides 19 db gain, + 31.7 dbm oip3, and 4.6 db noise figure while drawing 75 ma current. the device combines dependable performance with consistent quality to maintain mttf values exceeding 100 years at mounting temperatures of +85c. the device is housed in a lead - free/green/rohs - compliant industry - standard sot - 89 package. the tqp36 9185 consists of a darlington - pair amplifier using triquints high reliability ingap/gaas hbt process technology . internal active bias enables ope ration with o nly dc - blocking capacitors and an rf choke on the dc bias feed. th is broadband mmic amplifier can be directly applied to various current and next generation wireless technologies such as cdma, w - cdma, and lte. in addition, the tqp36 9185 will work for other various applications within the dc to 6 ghz frequency range. ordering information part no. description TQP369185 ingap/gaas hbt gain block TQP369185 - pcb 0.5 - 4 ghz evaluation board standard t/r size = 2500 pieces on a 13 reel
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 2 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com rec ommended operating conditions parameter min typ max units v cc +4.75 +5 +5.25 v t case ? 40 +85 c tj ( for >10 6 hours mttf ) +170 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. absolute maximum ratings parameter rating storage te mperature ? 55 to 150c rf input power, cw, 50, t=25 c + 25 dbm device voltage (v cc ) +7.0 v operation of this device outside the parameter ranges given above may cause permanent damage. electrical specifications test conditions unless otherwise note d: v cc = 5 v , t case = +25c, 50 system parameter conditions min typ max units operational frequency range dc 6000 mhz test frequency 1900 mhz gain 17.5 19 20.5 db input return loss - 13.5 db output return loss - 9.6 db output p1db +19.6 dbm output ip3 pout=0 dbm/tone, f= 1 mhz +28 +31.7 db m noise figure 4.6 db device voltage ( v cc ) 5 v device current (i cc ) 55 75 92 ma thermal resistance ( jc ) junction to base (1) 82 o c/w notes: 1. thermal path is from device junction through package ground tab (pins 2,4) to mounting surface.
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 3 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com s - parameters test conditions: v c c =+ 5.0 v (typ.), i cc = 72 ma (typ.), tcase=+25 c, unmatched 50 system, calibrated to device leads freq ( m hz) s11 (db) s11 (ang) s21 (db) s21 (ang) s12 (db) s12 (ang) s 22 (db) s22 (ang) 10 - 19.3 - 178.5 21.3 179.4 - 26.2 0.5 - 14.3 3.2 20 - 19.0 - 177.3 21.4 178.6 - 26.1 0.5 - 14.0 1.0 50 - 18.6 - 175.6 21.4 177.6 - 26.0 - 0.4 - 14.3 - 2.7 100 - 18.4 - 176.9 21.3 174.5 - 26.1 - 0.3 - 14.4 - 8.5 200 - 17.9 - 170.6 21.3 169.7 - 26.1 - 0.6 - 14.0 - 16.2 500 - 16.9 - 169.8 21.0 155.4 - 26.0 - 2.7 - 13.4 - 43.7 1000 - 14.3 - 173.6 20.5 132.9 - 25.6 - 6.1 - 12.0 - 83.8 1500 - 12.3 178.7 20.0 110.6 - 25.1 - 10.7 - 10.4 - 119.2 2000 - 10.7 163.5 19.3 89.1 - 24.5 - 18.4 - 8.9 - 149.9 2500 - 9.1 148.7 18.5 68.1 - 24.2 - 26.3 - 7.9 - 177.8 3000 - 7.8 136.2 17.7 49.2 - 23.8 - 34.8 - 7.0 160.8 3500 - 6.9 125.7 16.8 30.8 - 23.5 - 44.4 - 6.3 141.0 4000 - 6.5 115.7 15.8 12.5 - 23.5 - 53.7 - 5.3 122.0 4500 - 6.7 101.4 14.7 - 4.6 - 23.7 - 62.5 - 5.0 104.1 5000 - 5.8 89.6 13.7 - 19.6 - 23.5 - 69.4 - 4.7 90.3 5500 - 4.8 80.2 13.1 - 36.1 - 23.5 - 79.2 - 4.1 78.6 6000 - 4.3 69.8 12.1 - 52.3 - 23.7 - 89.4 - 4.0 66.0
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 4 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com tq p369185 - pc b evaluation board c2 c1 l1 c3 j4 j3 j1 j2 q1 r1 q1 j2 rf output j4 gnd j3 vcc 1 2,4 3 j1 rf input l1 39 nh c3 56 pf c2 56 pf c1 0.018 uf notes: 1. see evaluation board pcb information section for material and stack - up. 2. all components are of 060 3 size unless otherwise stated. 3. zero ohm resistor r1 is used to bridge a trace gap on pcb 1075825 an d is not required in end user applications. bill of material ? TQP369185 - pcb reference des. value description manuf. part number q1 n/a high linearity lna gain block triquint tqp36918 5 c1 0.018 uf cap, chip, 0603, 16v, x7r, 10% various c2, c3 56 pf cap, chip, 0603, 50v, npo, 5% various l1 39 nh inductor, 0603, 5%, cs series coilcraft r1 0 res, chip, 603, 1/10w, 5% various component values for specific frequencies use the component values in this table for optimal operation at specific frequencies . reference designator frequency (mhz) 50 500 900 1900 2200 2500 3500 l1 820 nh 220 nh 68 nh 27 nh 22 nh 18 nh 15 nh c2, c3 .018 uf 1000 pf 1 00 pf 68 pf 68 pf 56 pf 39 pf
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 5 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com typical performance ? TQP369185 - pcb test conditions unless otherwise noted: v supply =+5 v, i cc = 7 5 ma, t case = +25 c parameter typical value units frequency 500 900 1900 2100 2600 3500 4000 5000 6000 mhz gain 20.5 20.4 19.0 18.6 18.0 16.8 15.8 13.7 12.1 db input ret urn loss 11.7 12.4 12.3 13.3 13.7 - 6.9 - 6.5 - 5.8 - 4.3 db output return loss 17.8 15.9 10 9.3 8.7 - 6.3 - 5.3 - 4.7 - 4 db output p1db 20.9 +19.8 +19.6 +19.5 +19 +17.5 +15.8 +13.9 +12.3 dbm oip3 +33.3 +32.3 +31.7 +31.7 +30.6 +28.6 +27.1 +24.4 +23.4 dbm noi se f igure 4.5 4.7 4.6 4.7 4.8 4.9 5.1 5.6 6.3 db notes: 1. oip3 measured with two tones at an output power of 0 dbm / tone separated by 1 mhz. performance plots ? tqp36918 5 - pcb test conditions unless otherwise noted: v supply =+5 v, i cc = 7 5 ma, t case = +25 c 10 12 14 16 18 20 22 0 1 2 3 4 5 6 |s21| (db) frequency (ghz) gain vs. frequency +85 c +25 c 40 c - 20 - 15 - 10 - 5 0 0 1 2 3 4 5 6 |s11| (db) frequency (ghz) input return loss vs. frequency +85 c +25 c 40 c - 20 - 15 - 10 - 5 0 0 1 2 3 4 5 6 |s22| (db) frequency (ghz) output return loss vs. frequency +85 c +25 c 40 c 29 30 31 32 33 34 - 3 - 2 - 1 0 1 2 3 4 5 6 7 oip3 (dbm) output power/tone (dbm) oip3 vs. output power/tone +85 c +25 c c freq. =900 mhz 1 mhz tone spacing 29 30 31 32 33 34 - 3 - 2 - 1 0 1 2 3 4 5 6 7 oip3 (dbm) output power/tone (dbm) oip3 vs. output power/tone +85 c +25 c c freq. =1900 mhz 1 mhz tone spacing
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 6 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com pin configuration and description rf in gnd rf out gnd 1 2 3 4 pin no. label description 1 rf in rf i nput, matched to 50 ohms. external dc block is required. 3 rf out rf o utput / dc supply , matched to 50 ohms . external dc block and bias choke, are required. 2, 4, backside paddle gnd paddle rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance. see pcb mounting pattern for suggested footprint. evaluation board pcb information triquint pcb 10 75825 material and stack - up 50 ohm line dimensions: width=0.028" spacing=0.028"
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 7 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com package marking and dimensions marking: part number C 369185 lot code C aaxxxx 0.10 (0.004) 3 places m t s z y s 1 2 3 -z- 4 1.62 (.064) 4.40 (.173) .35 (.014) .36 (.014) .44 (.017) 1.40 (.055) d1 d c b1 b symbol a 4.60 (.181) 4.50 (.177) 1.83 (.072) 1.73 (.068) 1.60 (.063) max .44 (.017) .48 (.019) .56 (.022) .50 (.020) .40 (.016) .42 (.0165) 1.50 (.059) typ min 2.2 (.087) 3.94 (.155) 2.13 (.084) 2.29 (.090) m e h l e1 e1 e symbol 2.6 (.102) 2.40 (.095) 2.29 (.090) 2.60 (.102) 4.25 (.167) 1.20 (.047) 1.50 bsc (.059) 1.10 (.043) 4.10 (.161) 3.00 bsc (.118) 2.20 (.087) 2.50 (.098) max min .89 (.035) typ 7 a b e e1 2x b1 e l h d1 d -y- c -t- e1 m d1 d1 alternate backside patterns - reflow compatible (part may be supplied with either pattern) n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. dimension and tolerance formats confor m to asme y14.4m - 1994. 3. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp -012. 4. contact plating: nipdau pcb mounting pattern 3.86 [0.152] 0.64 [0.025] 2x 0.86 [0.034] 0.76 [0.030] 0.63 [0.025] ?.254 (.010) plated thru via holes 1.26 [0.050] 2x 1.27 [0.050] 0.86 [0.034] 2x 0.58 [0.023] 4.50 [0.177] 2.65 [0.104] package outline 3.86 [0.152] 29x 3 n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. 4. do not remove or minimize via hole structure in the pcb. thermal and rf grounding is critical. 5. we recommend a 0.35m m (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 6. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 369185 aaxxxx
t qp369185 dc- 6 ghz gain block datasheet: rev e 7/1 6 /13 - 8 of 8 - disclaimer: s ubject to change without notice ? 2013 triquint www.triquint.com product compliance information esd sen sitivity ratings caution! esd - sensitive device esd rating: class 2 value: 2000 v to < 4000 v test: human body model (hbm) standard: jedec standard jesd22 - a114 esd rating: class iv value: 3dvvhv9 test: charged devic e model (cdm) standard: jedec standard jesd22 - c101 solderability compatible with both lead - free (260c maximum reflow temperature) and tin/lead (245c maximum reflow temperature) soldering processes. contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating: level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifications, additional product information, worldwide sa les and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@t riquint .com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@ triquint .com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the informa tion contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notic e. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, l icenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or lif e - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
|
